Service - Quality - Commitment

Toll Free: 800-991-1280

Local: 713-675-0123

One of the least expensive pointing operations applied at the time of heading. This operation provides an end chamfer starting with a diameter smaller than the root diameter of the thread. The minimum reduction of the point is approximately 10% below the maximum minor diameter with an included angle of 40 to 50.

A straight pointed section reduced in diameter slightly below the root diameter of the thread. Usually extending In length about two-thirds the diameter of the thread. Recommended for ease In starting, to insure against stripping fine threaded products, and to increase efficiency along production lines.

An efficient method of producing pointed long studs or long screws with an end chamfer similar to the Die Point. The last thread and a half is slightly cupped by the thread roll-over operation.

(ROUNDED): An Inexpensive method of applying a 40',60' or go' lead-in point having a slightly rounded contour but with pinch-off marks on Its surface. Used for aligning several. sheets or assembling several parts requiring pilot action.

(PINCHED): Usually supplied with an approximate 45' Included angle having a sharp point and slightly squared surface. Used for Impinging or locking against wood or other solt material. Other degrees of Included angle and sharpness also available.

A special cup section supplied on the end of the threaded member having a depression In the end to reduce the area In contact with the surface which increases Its holding and locking power under pressure.

A dome-like rounded surface applied to the end of a threaded member In order to offer pressure without disfigurement. Used for adjusting, members where friction without cutting action Is desirable.

A precision forming operation to provide any required Included angle. Offers a smooth surface, accurate length, and a sharp point which can be produced to any desired contour to fit your particular requirements.

A thread forming screw for use in thin metal .015 to .050 thick. Used with drilled, punched or nested holes in sheet metal, resin impregnated plywood, asbestos combinations, among others. Not recommended for new design.

A thread forming screw for use In heavier metal .050 to .200 thick. Larger root diameter with finer thread pitch for light and heavy sheet metal non-ferrous castings, plastics, Impregnated plywood, asbestos combinations, and other materials.

A thread forming screw combining locating type point of Type A with thread size and pitch of Type B. Normal limitations of Type B apply.

A thread forming screw with either coarse or fine pitch machine screw thread and blunt tapered point. Eliminates chips and permits replacement with standard screw In the field. Higher driving torque required. Usable In heavy sheet metal and die castings.

A thread forming screw with high Helix thread for driving or hammering into sheet metal, castings, fiber or plastics for permanent, quick assemblies.

A thread cutting screw with machine screw thread with blunt tapered point. having multi-cutting edges and chip cavities. For heavy gauge sheet metal. aluminum, zinc and lead die castings, cast Iron, brass and plastic.

A thread cutting screw with a tapping screw thread with blunt tapered point and multi-cutting edges and chip cavities. For plastics, die castings, metal clad and resin impregnated plywood, and asbestos.

A thread cutting screw with single flute for general use. Produces a fine standard machine screw thread for field replacement.

A thread cutting screw for wood with a coarse tapping screw thread and a special long sharp point fluted to capture chips.

A thread cutting screw in the fine thread series offering maximum thread cutting area and excellent chip clearing, with minimum tightening torques.

A thread cutting screw similar to Type 23 point except with coarse Type B thread. For plastics and other soft materials with large chip clearing and cutting edges.

With special drilling points-lengths-diameters that will drill through '1/4" metal. Eliminates all hole preparation-drills faster than a drill. No punching: drilling or tapping required. Reduces die costs.

Produces more secure sheet metal assemblies faster...used as self-drilling screw or driving thru pre-punched holes. Can be used with or without' pilot holes. Positive rake "forward cutting edge" drills straight thru sheet metal at peak speed. Perfectly mated threads Increase strip and back out pressures.

If you do not see what you are looking for or need more information, please contact us we will be happy to help you!

iso.gif
Zero Products, Inc.

219 Baywood

Houston TX 77011

Toll Free: 800-991-1280

Fax: 713-675-6066

Local: 713-675-0123

zerofast@zerofast.com